vauxr-openclaw

An OpenClaw channel plugin that bridges Vauxr voice devices into the OpenClaw agent loop. It connects to Vauxr over WebSocket, dispatches inbound transcripts to the agent, and streams response deltas back for TTS playback.

It also registers three agent tools for direct device control from any session.

---

How it works

Channel Plugin Bridge (recommended)

Vauxr  <──WS (Vauxr protocol)──>  vauxr-openclaw plugin  <──>  OpenClaw agent loop

• The plugin opens an outbound WS connection to Vauxr on startup
• Inbound transcripts from devices are dispatched into the agent loop as vauxr:{device_id} sessions
• Agent response deltas stream back to Vauxr in real time for TTS playback
• A before_prompt_build hook injects a voice-optimized system prompt for all vauxr sessions

Fallback: Direct Operator WS

Vauxr  <──WS (OpenClaw protocol)──>  OpenClaw gateway

If installing the plugin is undesirable, Vauxr can connect directly to the OpenClaw gateway as an operator. This still works but is limited:

• No voice system prompt injection
• No session detection for vauxr-specific behavior
• No plugin-side control over prompt or session routing

To use fallback mode, configure Vauxr with OPENCLAW_URL and OPENCLAW_TOKEN environment variables and do not install this plugin.

---

Tools

Tool	What it does
vauxr_devices	Lists all Vauxr devices connected to Vauxr, with their IDs, names, and connection state
vauxr_announce	Synthesizes text via Piper TTS and plays it through a device's speaker
vauxr_control	Sends a control command to a device (set_volume, mute, unmute, reboot)

These tools use the Vauxr REST API and work in any session, not just vauxr voice sessions.

---

Requirements

• OpenClaw gateway
• Vauxr running and reachable
• At least one paired Vauxr device connected to Vauxr

---

Installation

Install from the repo directly:

openclaw plugins install path:/path/to/vauxr-openclaw

Then configure in your OpenClaw config:

{
  "channels": {
    "vauxr": {
      "url": "http://vauxr:8765",
      "token": "your-channel-token",
      "voiceSystemPrompt": "You are responding to a voice device. Use plain speech only — no emojis, no markdown, no code blocks. Keep replies concise."
    }
  },
  "plugins": {
    "entries": {
      "vauxr": {
        "enabled": true,
        "hooks": {
          "allowPromptInjection": true
        }
      }
    }
  }
}

• url — Vauxr base URL (HTTP)
• token — channel token generated in the Vauxr portal
• voiceSystemPrompt — optional, appended to the system prompt for all vauxr sessions

The allowPromptInjection hook permission is required for the voice system prompt to take effect.

---

Usage

Once installed, the plugin connects to Vauxr automatically. Voice turns from any device are routed through the plugin into the agent loop, and responses stream back for TTS playback.

The agent tools are available in all sessions:

Announce something:

"Announce through the living room speaker that dinner is ready."

Device control:

"Mute the bedroom speaker." "Turn the volume up on the kitchen device."

---

Architecture

Vauxr device (mic)
    │
    │  voice.start / audio / voice.end
    ▼
Vauxr (STT: Whisper)
    │
    │  channel.transcript (WS)
    ▼
vauxr-openclaw plugin
    │
    │  subagent.run(sessionKey: "vauxr:{device_id}")
    ▼
OpenClaw agent loop
    │
    │  agent event deltas
    ▼
vauxr-openclaw plugin
    │
    │  channel.response.delta (WS)
    ▼
Vauxr (TTS: Piper)
    │
    │  0x02 audio frames
    ▼
Vauxr device (speaker)

---

License

Vauxr OpenClaw is licensed under the MIT License.